Water Proofing Solutions

EMB Elastomeric Membrane is a liquid applied coating based on polyurethane prepolymers extended with tar, which cures by reaction with atmospheric moisture to give a continuous film that is rubber-like and elastic. Coal tar pitch extended, one pack moisture curing polyurethane offering cost effective, heavy duty waterproofing.

EMB is a high solid coating designed to give a high-build film. It can be brush or spray applied ( with airless spray equipment ) but it has a higher viscosity than a conventional paint and should not be diluted.

EMB is a membrane coating, not a paint and as such protection is only achieved with a high film build, i.e. 1 mm on flat surfaces minimum. It is therefore essential that this be achieved. The membrane can be applied in one 1 mm or two 0.5mm coats.

EMB is a Coal Tar based, liquid applied, moisture curing PU membrane

Target application is the same for both; waterproofing. Bitumen extended products are preferred by some clients. EMB is a moisture curing product and so the viscosity is affected by picking up moisture from the atmosphere. In the case of EMB the product is immediately packed and sealed

Into the 20 litre tins in a controlled way.

Product is designed for waterproofing below tile or screed, such as for roofs and balconies, above and below ground tanking, internal wet areas such as shower units. In these application areas, the product is not exposed to UV and therefore it will last a long time. Product is designed to last 10 years.

One pack, moisture curing polyurethane extended with aluminium leaf. On application, the leaf migrates to the surface and interlocks forming a UV barrier which is extremely solar reflective and weatherproof.

EMA elastomeric membrane is a liquid applied coating based on urethane prepolymers which cures by reaction with atmospheric moisture to give a continuous film which is rubbery and elastic. It contains leafing aluminium which gives excellent U.V. resistance. EMA is a very high solid coating designed to give a high-build film. It can be brush or spray applied ( with airless spray equipment ) but it has a higher viscosity than a conventional paint and should not be diluted.

Elastomeric membranes are designed to bond to many types of substrate particularly those commonly used as roofing, such as felt, asphalt, slate, tiles, asbestos, concrete, brick, wood, glass and metals. They can also be applied to spray polyurethane (PU) foam insulation. However, it is essential that the substrate and structures are properly prepared, and stable.

We offer heavy-duty spray elastomers and Polyurea coatings for use in the industrial, marine and civil engineering sectors.
ADVANTAGES :

Fast Set Protective Coatings
The "Armour-Range" are market-leading polyurea / polyurethane hybrid coatings that cure in seconds and can be put into service in minutes. They offer exceptional resistance to mechanical abrasion and chemical attack along with high tensile elongation and crack-bridging properties. Applications are diverse and include bund wall lining, coating of manhole access chambers and pipe protection.

Civil Engineering
The "Armour-Range" are 100% solids, high build coatings which provide 100% adhesion to all substrates commonly used in construction including concrete and metals.

Truck Bed Lining
The toughness and abrasion resistance of the "Armour-Range" make them ideal for use as sprayed-in-place truck bed liners. Being 100% bonded, they offer excellent resistance to water damage, corrosion and other problems associated with traditional drop-in-liners.

Potable Water & Food Contact
ARMOUR - FLEX PW is a 100% solids polyurea elastomer designed as a monolithic, seamless, waterproof liner for where there is direct contact with potable water or food products. It is WRAS, ANSI / NSF 61 and USDA approved. In addition it has proven its performance in frozen food cold stores.

Products

We are pleased to announce the following additions to the TV, Film & Exhibitions range - Armour-Shield is a general purpose Class 1 fire resistant pure polyurea. Armour-Form is a soft and flexible replication and moulding polyurea elastomer. Armour-Rock is our toughest material yet, a reinforcement and moulding polyurea elastomer, also having Class 1 fire resistant properties.

"Armour-flex" and "Armour-lyte"
"Armour-flex" and "Armour-lyte" are the market-leading products for armour and leather reproduction, having been used on Knights Tale, and the Alexander and Troy films. The materials are highly versatile and productive on application, with the sprayed liquid setting to a solid and being ready to de-mould in seconds. The results are aesthetically outstanding and the pieces robust enough to withstand even the hardest treatment on set / location.

"Armour-flex" and "Armour-lyte" are also superb general purpose coatings for the protection of polystyrene and polyurethane foam pieces.

Armour-Shield is a general purpose Class 1 fire resistant pure polyurea. Armour-Form is a soft and flexible replication and moulding polyurea elastomer. Armour-Rock is our toughest material yet, a reinforcement and moulding polyurea elastomer, also having Class 1 fire resistant properties.

Sprayed Polyurethane Foams
We supply a wide range of sprayed polyurethane foams, the most commonly used in set construction being "Agrispray®" and "Exo-set". "Agrispray®" offers a superior alternative to plastering, being lighter in weight and far quicker to set. It is often used for cave and rock effects. "Exo-set" is a high density spray system used typically where pieces require minimum thickness but maximum strength, such as reproducing roof tiles or supporting shields.

We manufacture a range of hand mix, rigid, polyurethane foams with densities from 30 kg/m³ to 500 kg/m³.

We are one of the trustworthy firms, involved in offering a wide gamut of UV Stable Aliphatic Polyurea Elastomer to our clients. Our professionals make genuine efforts to provide this coating service within promised set of time span. While rendering these coating services, we utilize advanced technicians in order to enhance special emphasis on superior quality.

FOAMSHIELD is a composite two component coating system consisting of a brown urethane base coat and a light grey urethane top coat. The FOAMSHIELD system is used for all roofing applications where permanent ponding water is not a problem. The system can withstand 1" of ponded water over 10m² per 48 hours. Ponding conditions in excess of this demand special consideration, and reference should be made to our Technical Department. The system is designed for use on sprayed polyurethane foam, but can be applied to other surfaces provided due consideration is given to priming and joint preparation.

Advantages and Benefits :

PD2000 : Low free TDI monomer Polyurethane Prepolymer
PD2000 pre-polymer is a new, high performance, TDI based polyurethane pre-polymer with a low free monomer content.
Uses : PD2000 can be used in various sealing and coating applications both in one and two pack products, and is particularly suitable for use in the manufacture of one component, moisture curable, flexible, seamless membrane coatings. Other applications include joint fillers, pipe coatings and binding for cork, rubber, foam etc.

1200PP: Polyurethane Prepolymer
1200PP is a polyfunctional, medium molecular weight, MDI based polyurethane prepolymer with terminal isocyanate groups.
Uses : 1200PP shows a particular advantage when used as an adhesive for wood or similar substrates, other applications include primers of various coating systems and sealers for other porous substrates. Isothane 1200PP is used in a wide variety of applications, mainly in one component products.

1248PP Polyurethane Prepolymer
The 1248PP series is a range of polyfunctional, medium molecular weight, MDI based polyurethane prepolymers with terminal isocyanate groups.
Uses : The 1248PP series can be used in various sealing, priming and adhesive applications, mainly in one pack products. Certain members of the range are particularly suitable for use in the manufacture of one component, moisture curable, flexible concrete sealers. Other applications include primers of various coating systems and sealers for other porous substrates.

1602PP : Prepolymer
1602PP is an MDI based polyurethane prepolymer which may be used as the basis for a range of moisture curing polyurethane coating systems.
One of the applications of 1602PP is in the manufacture of solvent based moisture curing polyurethane floor coating designed to provide a long lasting economical floor sealer.
Typical Applications : Floor coating systems based on 1602PP can be used on most surfaces including concrete, cement, asbestos, granolithic floors, plywood and many others.